MG Chemicals SAC305 Lead Free Tip Tinner, (28g) 1 oz container, No Clean Formulation

Description:

About this item:

  • Lead free Sn96.6/Ag3/Cu0.5 alloy
  • Effective at repairing oxidized iron tips
  • Prolongs the life of new iron tips
  • Non-corrosive
  • Easy to use
  • The 4910 Tip Tinner is a lead-free mixture used for quickly cleaning, repairing, and maintaining solder iron tips. It is composed of SAC305 powder mixed with some thermally stable, oxide-reducing compounds that form a convenient tinning block. The re-tinning compound is suitable for both leaded and lead free applications.
    During use, a soldering iron tip can lose its protective layer of tin leading to oxidization. Oxidized tips exhibit poor heat transfer characteristics and lose their ability to accept solder. This leads to bad joint formation and prematurely damages the soldering iron tip. To extend the soldering tip lifespan and decrease solder joint failures, any de-tinned tip should be re-tinned as needed. The 4910 Tip Tinner re-tins better than standard rosin-cored wires and results in a more robust, oxide protective tin layer.
    The 4910 Tip Tinner also offers better cleaning than pads or wet sponges. Carbonized resin can be removed by simply wiping the soldering tip against the re-tinning compound without requiring heavy pressure or mechanical scrubbing.
    To open the container: Remove the plastic wrap around the container. Use a small, pointed object like a screw driver to gently lift the lid straight up without using excess amount of force.
    –OR–
    Remove the plastic wrap around the container. Twist the cap and gently open without using excess amount of force. To clean or re-tin soldering tips
    1. Bring the soldering iron to its standard operating temperature.
    2. Roll or wipe the tip on the surface of the tip tinner. This should produce local melting.
    3. Wipe tip on a wet sponge to remove potential post-tinning residues."

    Review:

    4.8 out of 5

    95.38% of customers are satisfied

    5.0 out of 5 stars Top Tips

    S.J.C. · 26 February 2017

    This works well - it very quickly resurrected a tip that refused to hold solder. Comes complete with 'Can You Open Me?' game - lol. I needed to use two mole grips to carefully open the tin, as a prize you get to tin your tips ;)

    5.0 out of 5 stars Lid comes off no problem

    M.G. · 9 September 2023

    I was really prepared for battle reading the reviews stating people using a vice and mole grips to open the pot.Admittedly it was not possible with my bare hands but I ran my nail around the seam to find the biggest gap and then used a 2.5mm flat head screwdriver against the seam and pushed in and up. The lid popped right off and made a lovely noise too.The formula contains 96.5% tin 3% silver and 0.5% copper which I find to be preferable.

    5.0 out of 5 stars Easily get a tip soldering again

    R. · 11 March 2022

    It was an absolute nightmare getting a cooked tip wetted agsain before i had this. It's great.

    5.0 out of 5 stars Really good stuff

    C. · 2 October 2017

    Really good stuff. If you are rubbish at soldering, have a crappy soldering iron, with an old tip: get this and a flux pen and you will be golden.

    4.0 out of 5 stars Cleaning & tinning old tips.

    s. · 8 December 2017

    Cleaned an old (but unused ) tip with it. It took a few goes at it but it gradually cleaned it up nicely ! Thanks very much !

    5.0 out of 5 stars Does the job

    M.J.G. · 18 August 2019

    This tip tinnier works perfectly and is really good value for money

    3.0 out of 5 stars Did the job. Only three stars as it took ...

    D.G.P. · 30 December 2016

    Did the job. Only three stars as it took about 30 minutes and some special tools to safely open the tin. It had been jammed shut and then sealed with clear tape. Managed it in the end without impaling my hand with the tools.

    5.0 out of 5 stars Essential little tin.

    D. · 19 September 2017

    This does a perfect job of tinning the tip. Very easy and quick tin, just roll the tip over the surface as the iron reaches temperature, until you get a good tin. Easy and it lasts too.

    Good product

    G. · 20 May 2024

    Good product. Soldering iron more efficient when using it

    Deja bien la punta del soldador

    M.L. · 4 July 2022

    Me dejó muy bien la punta del soldador, cumple su función

    genial

    A.C. · 18 December 2024

    Por fin la punta de mi soldador siempre brillante y lista para soldar con este producto.

    Ottimo

    A. · 14 December 2024

    Non conoscevo questo prodotto, sono rimasto stupito..utilissimo

    Works great!

    P. · 23 October 2023

    Top notch stuff, my soldering tips are as good as new!

    MG Chemicals SAC305 Lead Free Tip Tinner, (28g) 1 oz container, No Clean Formulation

    4.5

    BHD10539

    Quantity:

    |

    Order today to get by

    Free delivery on orders over BHD 20

    Return and refund policies

    Product origin: United Kingdom

    All product information listed on the site are from 3rd party sources, including images and reviews. bolo.bh is not liable for any claims or promotions mentioned on the product description or images with textual content. For detailed product information, please contact the manufacturer or Bolo support by logging into your account. Unless stated otherwise during checkout, all import taxes and duty are included in the price mentioned on the product page. bolo.bh follows the rules and regulations of sale in Bahrain and will cancel items in an order that are illegal for sale in Bahrain. We take all the necessary steps to ensure only products for sale in Bahrain are displayed. Product stock and delivery estimate may change with the seller even after placing the order. All items are shipped by air and items marked “Dangerous Goods (DG)” by the IATA will be cancelled from orders. We strive to process your order as soon as it is finalized.

    Similar suggestions by Bolo

    More from this brand

    Similar items from “Tip Cleaners”