Choose your country
Delivery choices and times vary depending on your location
Description:
About this item:
Review:
4.9 out of 5
97.78% of customers are satisfied
5.0 out of 5 stars Works well with Yamaha F300
Drained the oil on my Yamaha F300 as well as my 9.9 Yamaha outboard motor. Easy to use, quality product,highly recommended.
5.0 out of 5 stars Best tool for bleeding brakes or changing oil. Love this tool. But has some issues.
I bought this unit in the larger size because I have a Dodge Cummins diesel that holds 12quarts of oil. I also have used it on my Prius and on my daughters sailboat Perkins motor. It has worked perfectly so far. Now for the best part. Last week I had to do rear brakes on my dodge diesel 3500. I had ordered the brake bleeder additional part. After replacing the pads I decided to do a brake fluid flush. I removed the master cylinder cap and was able to suck all the fluid out of the dual reservoir and refilled it with fresh fluid. Onto the furthest wheel from the master cylinder, turn the bleeder valve on this tool to off pump it down attach the hose to the bleeder, crack the bleeder and open the valve. Suck out enough fluid until fluid runs clear. Tighten down bleeder screw. Refill the master cylinder reservoir and repeat. Oh man, a one man bleeder and a huge tank so I never have to dump fluid between wheels. This thing worked great! I have used those finger pump bleeder suckers and they just suck at sucking and you have to empty them 3 times per wheel. Those finger pumper bleeders cost 2/3 of what this costs! So simple to use and works great. I will never bleed again with those finger pumps. This is so much easier! To bleed a car or truck was the best part of this tool. Sucking oil is just an added benefit. Buy this, it’s a no brainer.P.S. the screw ring on the suction side of the tank seems backwards. The tube flange is actually on top of the screw ring. The ring-screw does not hold the hose onto the tank. After much head scratching I simply thought it was just incorrectly made. I scoured the manual and ,as is typical of offshore made products, the manual was useless. Then, I called them. They said it’s correct and the ring is under the tube flange to help push the tube flange off if it needs changing. Why don’t they add that piece of info in the directions? Really stupid! If I were the design engineer, I would make the flange fit under the ring and be done with it and rewrite the instructions. It would cost a one time set up and problem solved but I’m not the engineer and it is made in China. All this said, it seems well made, despite that glitch, and I will continue to use this very effective tool. Some have said that the suction tube is too short, and it is. It will not reach into the pan on larger engines and the flexible tube behind the hard tube is too short so the tank can’t sit on the ground when pumping the handle on a large vehicle or one that is both tall and a large engine. Like my 4WD 3500 truck. A 3 foot solid tube pickup and a 4 foot longer tank to hard hose would have worked better. I fixed that at Home Depot for about 10 $ but it seems silly that I have to deal with these deficiencies instead of the manufacturer. Are you at OEM listening?! Fix this.
5.0 out of 5 stars Perfect and SO simple
I use this fluid extractor on my yard equipment and it makes oil changes a breeze. No more spilling oil on the driveway. No more searching for the right combination wrench, fighting with drain plugs, or scraping my knuckles. 2.5 gallons is probably overkill for my needs, but my oil recycling center is far away and I’d rather wait until I have extracted enough oil to make the drive worth it.
4.0 out of 5 stars This really is great for oil changes. The manual truly is worthless
You're probably about 90% committed to converting to doing oil changes by the dipstick method, but not sure which one of these extractors to buy and really wondering if this is a reliable method to do it. I looked at the various other extractors sold by HF as well as the MityVac model, and realized that they're all about the same and ultimately I chose this one mainly because of the large capacity (engine holds 9 liters) and the easy Bolo return policy. And go ahead and convert to the dipstick method, it's so much easier and faster, and the results are just the same as draining the pan. And FYI, Mercedes recommends the vacuum method vs draining the pan for their cars, which I confirmed with one of their mechanics. So I figured if Mercedes approves of this method, there must be something to it.As far as changing the oil via the dipstick, this is definitely the way to do it. All the advantages are real as well as the time savings of not having to lift/jack the car up. Also, this eliminates that remote chance of giving your wife PTSD when she finds you dead and crushed under your car after the jackstands fail.As far as this pump goes, it works great but as many other reviewers have noted, the included manual for this extractor is junk. There is zero helpful information in there. Honestly all the information you need is in these user reviews. Also, as many have mentioned, the device itself looks to be designed by a drunk engineer. Lots of times you'll look at it thinking "What in the world?" trying to figure out what one particular hole/fitting does, or the purpose of a seemingly random nut which doesn't seem to do a thing, or why there are various tubes and parts that don't seem to do anything. Somehow, magically, despite these oddities, the pump does a great job.This extractor removed and held 8.5 liters of oil without a problem in 10 minutes, with definitely room to hold another liter, so the 9.5 liters is probably correct. As others have noted, there are no marks on the container so there really is no way to tell if you got all the oil out or how much you've got out. I'd do what another reviewer had recommended and suck up however much quarts of water your engine is expected to hold, mark the cannister, and then proceed to drain the water out and suck up the oil. It's the only way to confirm that 1, your hose was long enough to get to the bottom of the oil pain and 2, that you got all the oil out. Keep in mind that your engine may be a quart low so don't get too alarmed if you're short. If you've done your own oil before, you should have an idea what your car uses up and what to expect. And no mention of this anywhere, but the only way to empty the container is to remove the intake hose and just dump it out of the large opening.I've now done 2 oil changes and a brake flush with this extractor, and it definitely has made things super easy. The inner diameter of the dipstick tube is small, so get your engine to operating temperature to make the oil easy to flow. The suction power is good, although really no way to get any idea of how much vacuum you're creating, and the plastic is thick and durable. I'm happy I have it and I'm happy with this new way to changing the oil. If only the manual was usable, this would be a 5 star product.
Works great!
Two plus years in, this extractor works like a champ. I should have bought a larger size though because some of my vehicles hold 6 or more litres of oil. The unit I bought holds a little over 4 litres. Good quality hoses, extension tubes, etc. Recommended buy for lawn mowers, other yard equipment, or automotive use. Well made and durable!
Instructions are a little short. especially with regard to cleaning and emptying.
fantastic tool. No fuss, and easy to use.
2014 vw gli so easy
I admit, I was hesitant to buy this at first. Some people say the tube is too short to hit the oil pan. I have a 2014 vw gli. It is more than long enough. Maybe 10 minutes to Draw out oil. It works incredibly well.I will never pay to have my oil changed again.Note: this pump works well for my vw because the oil filter is at the top of the motor. If you plan to buy this for your car, and the filter happens to be at the bottom of the motor, you might as well just pull the drain plug.
Equipo de fácil operación, práctico y de buena calidad
El producto funciona muy bien para extraerle el aceite del cárter a los motores de los carros, es un buen producto y muy práctico.
Works great, no mess..
Best thing I ever bought no need to getunder the car ever again.
Visit the OEMTOOLS Store
OEMTOOLS 24389 Manual Fluid Extractor, 5.3L Oil Extractor, Automotive Tool for Engine Oil, Transmission Fluid, and Coolant
BHD56400
Quantity:
|
Order today to get by
Free delivery on orders over BHD 20
Product origin: United States
Electrical items shipped from the US are by default considered to be 120v, unless stated otherwise in the product description. Contact Bolo support for voltage information of specific products. A step-up transformer is required to convert from 120v to 240v. All heating electrical items of 120v will be automatically cancelled.
All product information listed on the site are from 3rd party sources, including images and reviews. bolo.bh is not liable for any claims or promotions mentioned on the product description or images with textual content. For detailed product information, please contact the manufacturer or Bolo support by logging into your account. Unless stated otherwise during checkout, all import taxes and duty are included in the price mentioned on the product page. bolo.bh follows the rules and regulations of sale in Bahrain and will cancel items in an order that are illegal for sale in Bahrain. We take all the necessary steps to ensure only products for sale in Bahrain are displayed. Product stock and delivery estimate may change with the seller even after placing the order. All items are shipped by air and items marked “Dangerous Goods (DG)” by the IATA will be cancelled from orders. We strive to process your order as soon as it is finalized.
Similar suggestions by Bolo
More from this brand
Similar items from “Fluid Evacuators”
Share with
X
Or share with link
https://bolo.com/