About this item:
4.5 out of 5
89.23% of customers are satisfied
5.0 out of 5 stars arrived quickly
(function() { P.when('cr-A', 'ready').execute(function(A) { if(typeof A.toggleExpanderAriaLabel === 'function') { A.toggleExpanderAriaLabel('review_text_read_more', 'Read more of this review', 'Read less of this review'); } }); })(); .review-text-read-more-expander:focus-visible { outline: 2px solid #2162a1; outline-offset: 2px; border-radius: 5px; } these little lights are pretty bright.
5.0 out of 5 stars Perfect
Easy to wire and install.
5.0 out of 5 stars Good Replacement for existing
I had existing old ceiling lights. I measured and these were a good fit. I replaced the old ones with these.They fit great and look good. They are way brighter but worked well for me.
4.0 out of 5 stars Lights good ..clips broken on some
In my 2nd box of lights found 3 had the clips fallen off rendering them useless I couldn't figure out how to make the clips go back on and have a spring in them so basically these are useless lights... Luckily for me they'll just spares anyway. Apart from this the lights a good quality have a great light and do not overly bright and obnoxious I installed them in the ceiling of the Lanai and they are perfect on a dimmer.The only other complaint I have is the wire connectors they come with they're so small and chintzy they useless and can't be used so don't even plan to use them there's no way in the US we could have cable small enough and legal to use these connectors.
5.0 out of 5 stars Good
Good
5.0 out of 5 stars Bright and easy to install
At first I was worried about the lights each needing their own junction box in the attic to make them up to code. Then I decided to barrel crimp the low voltage side of the little drivers and run an extended piece of low voltage wire so I could po it all the drivers in the dame box. I used a 2g nail on to a rafter and landed the drivers in their with a 2g switch plate for ventilation. Lights are brighter than I imagined and with a 2in hole saw and a little love tap to get them up into the ceiling they look and fit great! Any questions send me an email Tylerhudsonelectric@gmail.com
5.0 out of 5 stars Perfect!!!
Exceptional value for this 4 pack of lights. No need for a separate transformer. The lights work great, even on the lowest setting of a sliding dimmer switch. I used these for niche lights in my bar and they couldn't be better.
3.0 out of 5 stars say it with me CHHHIII NNAHHHH
These lights were not suitable for my use. 1. They are not IC rated, you run the risk of overheating or worse a fire 🔥. These light are cheap and made in CHHIII NAAHH (DT Voice) Which is fine but not US quality the cable plastic connector is very cheap and you cannot use standard Romex because of the fit and again very limited on where you can use them. They do not come with the wiring to the power source or each other so you have to run to Home Depot for wiring. These really depend on your use and where it is located. It cannot be used in wet location or outdoors just FYI.
Bright and as described
(function() { P.when('cr-A', 'ready').execute(function(A) { if(typeof A.toggleExpanderAriaLabel === 'function') { A.toggleExpanderAriaLabel('review_text_read_more', 'Read more of this review', 'Read less of this review'); } }); })(); .review-text-read-more-expander:focus-visible { outline: 2px solid #2162a1; outline-offset: 2px; border-radius: 5px; } Not bad for a small lightAngle does look a bit wider than 36 degrees but that is hard to tell. I will use them again.Connectors are bad but you can just take them out and use your own.I saw on some reviews they need 54mm hole instead of 51mm hole but i used my 51mm (2") bit and gently punched it in. Makes it tight fit. It could be a bit confusing for DIYers but for people who are used to them will get it easily.
Wrong size wood bit/saw requires 54mm and not 51mm.
I had to use 54mm wood bit instead of 51mm as described due to the slightly bulky springs that locates the light into the cupboard.
Au top
Parfait , installation rapide et description conforme, je recommande !
Make sure you have the right power
I was replacing two old lights, I plugged in the old wires but had no luck. I called an electrician, luckily he was out of town. I'm not a patient man, so I opened up the junction box above the vanity and I saw an old tranformer that had to be removed. I removed the old transformer and everything worked like a charm. The lights are beautiful and bright, exactly what I needed!
Faible consommation d'énergie
Facile à installer faible consommation d'énergie. Bonne luminosité.
Visit the LightingWill Store
BHD16500
Quantity:
Order today to get by
Free delivery on orders over BHD 20
Product origin: United States
Electrical items shipped from the US are by default considered to be 120v, unless stated otherwise in the product description. Contact Bolo support for voltage information of specific products. A step-up transformer is required to convert from 120v to 240v. All heating electrical items of 120v will be automatically cancelled.
Or share with link
https://bolo.com/